Brace height

[Murray]

You mean you don't have at least two shot-in spares and a couple of un-shot-in new strings for the season???

[Schme1440]

Originally Posted by Murray

You mean you don't have at least two shot-in spares and a couple of un-shot-in new strings for the season???

Nope. I never have done. I am never distrusting in my equipment so I never need that many spares. I do normally keep a spare shot in string but just havent bothered untill now. Have put the request in for 2 strings in BCY 8125 or what ever it is. Just waiting to see what colours they have in stock. WOuld make them myself but cant be asked with buying all the bits (in other words I cant afford to).

[buzz lite beer]

If your getting your strings made for you and it's not to late , ask for both loops to be top loop size, a slight though still noticable volume reduction is achieved.

[Schme1440]

Originally Posted by buzz lite beer

If your getting your strings made for you and it's not to late , ask for both loops to be top loop size, a slight though still noticable volume reduction is achieved.

So your suggesting slightly larger loop on the bottom to match the top one? Interesting. I will ask cheers.

[buzz lite beer]

works for me.

[Schme1440]

Originally Posted by buzz lite beer

works for me.

I imagine it deceases the angle of the loop when strung so must have some affect, good I hope.

[buzz lite beer]

perhaps, just make sure that you look to see where your nock point is to determine which way around the string goes, because good archers never put there strings on upside down

[Schme1440]

Originally Posted by buzz lite beer

perhaps, just make sure that you look to see where your nock point is to determine which way around the string goes, because good archers never put there strings on upside down

I put my limbs on upside down the other day. First time ever. Think I was holding te riser upside down. I always check my string. Shouldnt be a problem.

[bowcoach]

This may be of some help, I'm sure the majority of this you already know, but I figured I'd post the entire article for others in the group.

I always let the bow tell me what the proper BH is for any given set up and to do that follow the steps below:

This works pretty well I should add.
---------------------------------------------------------------------------
How to Determine the Proper Brace Height (String Height) for a Bow
By Daniel Perez, Archery Coach, USA.

Brace or string height is the distance between the pivot point of the grip and the string. The proper brace height is one that produces a quiet, but solid sound, and also one that facilitates tight groups.

String height is important because it influences when the arrow will leave the string. If your string height is too long, it could be due to having a string that is too short. Usually you will get contact on the arm near the elbow, which is also indicative of an improper set-up.

A string height that is too short is indicative of a long string, and often people will experience contact near the wrist close to the bow hand.

Having an improper string height can lead to poor results, including arrow clearance problems, tuning problems, and so on.

The proper string height is one that falls within a range for each bow length, for example:

66 inch bow = 8.375 to 8.625 inches, or 21.27cm to 21.91cm
68 inch bow = 8.5 to 8.75 inches, or 21.59cm to 22.23cm
70 inch bow = 8.625 to 8.875 inches, or 21.91cm to 22.54cm

However every bow and arrow configuration differs, therefore you have to locate the best brace height for your current set up. For an initial set up, I would recommend starting at the lower end of the recommended range.

For beginners, don’t worry so much about fine tuning, as you should spend that time worrying about form and execution.

More polished archers may benefit from a more finely tuned string height. To fine tune string height, try the following steps:

1. Start at the lower end of the recommended range.

2. To fine tune string height for your current set up, start at 30 or 50 meters. Use several standard sized pieces of paper, paper plates, or unused targets. For this example I will use targets.

3. On target number one, write the initial string height directly on the target. Shoot three arrows at the target. After pulling the arrows, detach the target face and set it aside.

4. Put three-four twists on the string, and re-set the nock height. Next, measure the new string height distance and write this on a new target. Shoot another three arrows.

5. Repeat the steps above until you notice that the groups are getting wider.

6. Next, select the target that has the best group, note the string height you have written on that target. This will be a good string height to work with.

7. To fine tune, set your brace height to the second best result from above. This time shoot from 70 or 90 meters*, and make only one twist at a time.


*Or shoot from the farthest distance you are able to comfortably and consistently group arrows.

This is a lengthy way to obtain the best brace height, but it works very well.

Once you have determined the best string height for your set-up, it is best to make sure that you always shoot with the same string height (considering you have made no other equipment changes). You can make a mark on your T-square to give you a reference and check the string height every time you string the bow, to ensure it is set correctly.

[bowcoach]

I should add that the examples of BH in this article I wrote do not necessarily represent what should be utilized for every recurve. This is just a generalization. For a more appropriate initial range refer to your bow's manual.

Hope that will assist...

Later,

-Daniel